MPA5500 A.C. POWER ADAPTOR
The MPA5500 enables any MTL5500 Series module that is normally powered from a nominal 24V DC supply (i.e. those that are not loop-powered) to be powered from a high-voltage AC supply.
It plugs into the power socket (terminals 13 and 14) of an MTL5500 module and clips securely onto the module housing. The 25V DC power output from the adaptor is sufficient to supply a single module and can be connected to any normal AC power source.
SPECIFICATION
Input voltage
85 – 265V AC, (45–65Hz)
Efficiency
71% typ. at 230V AC
Power dissipation
1.2W typ at 230V AC.
Input terminals
Cage-clamp terminals accommodating conductors up to 1.5mm2 stranded or 16AWG single-core
Input protection
internal fuse, not user serviceable
Output voltage
25Vdc ± 10%
Output current
120mA at 25V
Ambient temperature
Operating: –20 to +60°C
Storage: –40 to +80°C
Mounting
Plugs into and clips onto MTL5500 Series I/O module
It is not for use with any equipment other than MTL5500.
Humidity
5 to 95% relative humidity
Mechanical
Ingress Protection: IP20
Material: polycarbonate
Weight: 28g approx.
Standards compliance
EN 61326, EN 61010
PCS45/PCL45USB CONFIGURATOR FOR MTL CONVERTERS
The PCS45/PCL45USB configurator allows MTL converters to be configured from a standard PC running a Microsoft® Windows® operating system. It comprises PC software, provided on a CD (PCS45), and an ATEX certified interfacing link (PCL45USB). Converters can be configured from the safe area, while on-line, and configurations can be saved to disk and printed out when required. It is suitable for use with MTL4000, MTL4500, MTL5000 and MTL5500 series products.
SPECIFICATION
PcL45uSB hardware
Location
Safe area
Connections
Pc side: USB B(F) socket
Converter side: cable with 3.5mm jackplug, 3-pole for MTL4500 and MTL5500 series converters. An adapter cable is provided for other earlier MTL converters.
Cable lengths
Converter side (fitted): 1.5m
USB cable A(M) to B(M) (supplied): 2m
Ambient temperature limits
–10°C to +60°C operating
–20°C to +70°C storage
Humidity
5 to 95% relative humidity (non-condensing)
Weight
200g
PcS45 configuration software
Compatible with Windows 2000, Windows XP or Windows 7
Consult MTL for operation with any other operating system,
e.g. Windows Vista™.
Software medium
PCS45 supplied on CD
Updates are available at www.mtl-inst.com
Recommended minimum Pc configuration
Microsoft Windows 2000, Windows XP or Windows 7
20MB of available hard disc space
CD ROM drive
Available USB port
Printer (local or network)
MTL5991 24V Dc POWER SUPPLY
A DIN-rail mounted unit for locations where a dc supply is not readily available. The wide input power supply range makes this unit universally applicable and the 24V dc, 2A output will drive a useful number of MTL5000 and MTL5500 series modules.
SPECIFICATION
Power supply
85 to 264V ac 47 to 63Hz
Power dissipation within unit
7.2W @ 2A
Mounting
35mm DIN (top hat) rail
Output voltage
24V dc nom (23.64 min/24.36 max)
Output current
2A maximum (1.7A with <105V ac input)
LED indicators
Green: Power indication
Weight
310g
Ambient temperature
Operating temperature –10°C to +50°C
Storage temperature –40°C to +85°C
Terminals
Cage clamp type accommodating conductors up to 2.5mm2, stranded or single-core
Note: Segregation between hazardous and safe area wiring must be maintained.
MTL5500 SERIES POWERBUS KITS PB - 8T,16T,24T,32T
A quick and easy way to distribute DC power to MTL5500 Series modules. Each powerbus kit includes 4 single ferrules, 4 twin ferrules and 2 insulation displacement connectors (Scotchlok).
SPECIFICATION
Available in 4 different lengths:
PB - 8T = 8 connectors and loops
PB - 16T = 16 connectors and loops
PB - 24T = 24 connectors and loops
PB - 32T = 32 connectors and loops
Insulation material :
PVC
Conductor:
24 strands of 0.2mm dia (0.75mm2) standard copper
Insulation thickness :
0.5 to 0.8 mm
Current rating :
12A max
Operating temperature range :
–20ºC to +60ºC
Max voltage drop on 32 modules drawing 130ma max :
0.5V
CHOOSING A POWERBUS KIT
Choose a powerbus where the number of power plugs is greater than or equal to the number of isolators to be powered and if necessary cut the powerbus to the required number of terminations.
Note: To reduce the risk of excessive voltage drop or overcurrent do not connect powerbuses in series.
MTL5500 Series enclosures
SPECIFICATION
Construction
Glass reinforced polycarbonate base - DX070
Glass reinforced polyester base - DX170
Transparent polycarbonate lid
Protection
Dust-tight and water-jet proof to IEC529:IP65
Lid fixing
Captive fixing screws
Weight (excluding barriers/isolators) kg
DX070 0.8
DX170 2.6
Items provided
DIN rail - fitted
ETL7000 Earth terminals (2 x) - fitted
"Take care IS" front adhesive label
Cable trunking (except DX070)
Note: Isolators are not included.
Mounting
Wall fixing lugs provided. For further details refer to INM5500.
Tagging and earth rail
Accommodates MTL5500 Series accessories.
Permitted location
Safe (non-hazardous) area
Note: N. America/Canada - Enclosures are rated NEMA 4X so can be used in Class 1, Division 2 (gases) location, but check with local requirements and ensure all cable entries also conform. Additional warning label will be required on or near the enclosure, see installation details. Not suitable for Class II or III, Division 2 hazardous locations.
Approximate capacities (on DIN rail between earth terminals)
* Use these figures when IMB57 mounting blocks for tagging/earth are included.
Ambient temperature limits
Dependent on units fitted. See instruction manual INM5500.
|
Number of MTL5500 isolators |
|
DX070 |
4 |
(2)* |
DX170 |
10 |
(8)* |
MTL CPS STANDARD BACKPLANES
Backplane |
number of |
Safe-area |
MOUNTING KITS |
ACCESSORIES |
||||
Surface |
DIn–rail |
19–inch |
earth–rail |
Tagging |
Spare fuse |
|||
CPS04 |
4 |
Screw–clamp |
SMS01 |
DMK01 |
– |
– |
|
FUS1.0ATE5 |
CPS08 |
8 |
Screw–clamp |
SMS01 |
DMK01 |
– |
ERK08 |
TSK08 |
FUS1.0ATE5 |
|
|
|
|
|
|
|
|
FUS2.0ATE5 |
CPS16 |
16 |
Screw–clamp |
SMS01 |
DMK01 |
– |
ERK16 |
TSK16 |
or |
|
|
|
|
|
|
|
|
FUS2.5ATE5 |
CPS24 |
24 |
Screw–clamp |
SMS01 |
DMK01 |
HMP24 |
– |
TSK24 |
FUS4.0ATE5 |
CUSTOM BACKPLANES
MTL4500 series backplanes can be customised for specific applications and customer’s requirements. All the signals on the backplane are ‘safe-area’ so custom designs are possible without the need for certification. MTL offers a fast and efficient customising service upon request.
Many installations can benefit from the use of existing custom solutions. These provide reduced system wiring, modularisation of the channels to match the IO card. In addition diagnostics, such and line fault detection, can be grouped prior to connection into the system.
Remote cable connections:
In addition to the many DCS solutions, listed on a previous page, are backplanes and cables that are ideal when the isolators are mounted in remote cabinets and the signals need to be returned to the system via a multicore cable.
CP-DYN SERIES
FTA |
Size |
Function |
MTL modules |
CP-DYNB-AIO |
B |
16ch analogue input /output |
MTL4541, 4546Y, 4575 |
CP-DYNB-AI250 |
B |
16ch analogue input |
MTL4541, 4575 |
CP-DYNA-2AIO |
A |
16ch analogue input / outpu |
MTL4544, 4549Y |
CP-DYNB-DI |
B |
16ch digital input |
MTL4511, 4514 |
CP-DYNB-DILF |
B |
16ch digital input with LFD |
MTL4514 |
CP-DYNB-2DI |
B |
32ch digital input |
MTL4513, 4516, 4517 |
CP-DYNB-4DI |
B |
48ch digital input |
MTL4510 |
CP-DYNB-DO |
B |
16ch digital output |
MTL4521, 4521L |
CABLES
All FTAs use the Tyco 20 pin Dynamic series of connectors. Cables are fitted with a mating connector and free ends the other, for connection to the system card.
Cable ordering code
CABDYN20-0.5 0.5m cable
CABDYN20-1 1.0m
CABDYN20-2 2.0m
CABDYN20-3 3.0m
CABDYN20-5 5.0m
CABDYN20-8 8.0m
CABDYN20-10 10m
CABDYN20-15 15m
CABDYN20-20 20m
CABDYN20-25 25m
CABDYN20-30 30m
CPELCO SERIES
A range of dedicated backplanes to interface with MTL4500 series intrinsically safe isolator modules and the MTL HART maintenance system products. The backplanes offer a standard Elco interface connector for use in systems where the IS interfaces are remote from the DCS.
Backplane |
Function |
MTL module |
Cable |
CPM08-2AIO |
16ch AI 4-20 |
MTL4544/4576/4549Y x 8 |
Elco38 x 1 |
CPM08-2AV |
16ch AI 1-5V |
MTL4544/4576 x 8 |
Elco38 x 1 |
CPM16-AIO |
16ch AIO 4- |
MTL4541/4575/4546Y |
Elco38 x 1 |
CPM16-2AIO |
32ch AI 4-2 |
MTL4544/4576/4549Y x 16 |
Elco38 x 2 |
CPM16-2AV |
32ch AI 1-5V |
MTL4544/4576 x 16 |
Elco38 x 2 |
CPM08-DDI |
16ch DI |
MTL4513/4516 |
Elco38 x 1 |
CPM16-DO |
16ch DO |
MTL4524/4523R |
Elco38 x 1 |
CGM08-DO |
8ch DO |
MTL4521/4521L (loop powered) |
Elco38 x 1 |
Contact Person: Ms. Steven
| Sitemap